What BTU will one foot of three quarter inch fin tube baseboard hydronic heater produce with 100 degree f water entering?
Most output ranging from 560 to 600 btuh per foot, this is with 170 F water temps. I have no way to know your specifics from where I am.
1 person found this useful
I have the old convector heaters and use a heavy duty steam cleaner to get between the fins. Don't forget to put a towel underneath to catch the dirt!
Is athree quarter inch natural gas line for a home sufficent for a furnace and hot water heater and aventless heater with a total BTU rating of 160000?
ABSOLUTELY NOT , NO WAY as the gas supply has to be calculated by developed LENGTH and Specific gravity of the fuel. . Better off to figure NO until you check the LENGTH
You will need to give more information. The Btu's of baseboard is determined by the water temperature and the type and size of the element. Copper fin tube (copper pipe with a…luminum fins over it) heats up quick and loses heat quickly it also has many diameters of element (copper tube). Most common in residential is 1/2", 3/4" & 1" ID (the OD will be 1/8" or so larger). There is also Cast iron baseboard that heats up slowly and cools off slowly (this is a much more even and comfortable heat). You should never mix and match cast iron radiation and copper radiation of the same circuit it will cause large temperature swings in conditioned area. Tell us what the boiler temperature is set to and what the type of radiation is and you'll get an answer.
9 inches... 12/4=3 3â¢3=9 There are 12 inches in 1 foot. Therefore: (12 Ã· 4) Ã 3 = 9 inches in 3 quarters of a foot.
Assuming they are all serving the same room and you are talking about 110 volts. Wire the 3 heat strips in parallel and break the power source feeding the closest one to the s…tat with the stat and connect the common wire wherever you can catch the house common. Be sure the stat is rated to carry the TOTAL amperage of the 3 strips and that the circuit is rated to carry that same total along with whatever else if anything is on it.
How many btus must be removed from one pound of water at 200 degrees f for it to end up as ice at 30 degrees f?
There are 12 inches in one foot. Therefore, three quarters of a foot is equal to 3/4 x 12 = 9 inches.
Probably to reduce noise and friction during expansion and contraction.
Hot line in water heater leaves in one half inch and increases to three quarter Is this going to affect pressure?
It is going to decrease it some.
BTU's are not based on the length. To answer this question the wattage and voltage of the baseboard must be given.
2.3 gallons of water.
Slant Fin baseboards are high efficiency baseboards that can be bought at many different locations. They are simply and easy to install using either glue or finishing nails.
volume = pir 2 h pi = 3.1416 h = 100 feet r = 1/2 X diameter r = 1/2 X 3/4 inch / 12 inches/ft = 0.03125 square feet volume = 3.1416 X (0.03125)2 X 100 = 0.3 cubic feet
212 - 80 = 132 degrees temperature increase x 1 pound water = 132 BTU
It is three-quaters of one and one third of an inch (1 1/3 " or 4/3 of an inch). The question "what is one inch three quarters of" can be rephrased as an algebra problem. 1"… = 3/4 x where x is the unknown quantity that you are asking about. Multiply both sides of the equation by 4/3 and you get 4/3" = x which is the answer. One inch is three quarters of four thirds inches (four thirds inches can also be stated as an inch and a third).
There are two main benefits that a Hydronic Baseboard heater provides. The first benefit is that it allows zoning which means one can choose what rooms need heat. The second b…enefit is that it can heat up floors.