# What is the reciprocal of 25 feet per second?

# If you run 25 feet per second how fast will you run a 100 meter dash?

ANSWER: \n.
\n1 meter is equal to 3.2808399 feet.\nTherefore 328.08399 feet would take 13.12336 seconds to travel at 25 feet per second.

# Mph to feet per second?

1 mile = 5280 feet 1 hour = 3600 seconds so 1 mph = 5280 ft/3600 seconds = 1.466... fps

# How many feet per second at 25 mph?

You should memorize 60 mph = 88 feet per sec. Then (25 mph)/(60 mph)*(88 feet/sec) = 36.6666.... feet per second

# How fast is 1000 feet per second?

Equates to approximately 681.82 miles per hour.\nSupporting math -\nThere are 60 seconds in every minute (multiply 1000 X 60 = 60,000)\nThere are 60 minutes in every hour (multiply 60,000 X 60 = 3,600,000)\nThere are 5280 feet in every mile (divide 3,600,000 / 5280 = 681.8181818181) 1,000 feet per s…econd is 681.82 miles per hour. (MORE)

# How do you Convert mph to feet per second?

1 mile = 5280 ft, 1 hour = 3600 secs. So 1 mph = 5280/3600 = 1.47 ft/sec. For a ratio you can easily remember, 60 mph = 88 ft/sec

# What is the reciprocal of 25?

The reciprocal of one number is another number which when both are multiplied, give a product of 1. In the case of a whole number, the reciprocal is 1 divided by that number.... so the reciprocal of 25 is 1 / 25 or 0.04

# How do you convert feet per minute to meters per second?

Easy! Divide by 200. So 1000 feet per minute = 5 metres per second (roughly). It also equals 10 knots incidentally.

# What is the volume of a sphere after .25 second if the rate of the radius is 6 feet per second?

The formula for volume of a sphere is 3/4*pi*r^3, the formula for your radius with respect to time is 6ft/s, thus we have the formula for volume of the sphere over time as (108/4)*pi*t^3 where t is in seconds and 108/4=27 cu ft. Thus V=27*3.14159*(0.25)^3=1.325 cubic feet.

# Speed of sound in feet per second?

Notice: The speed of sound changes with temperature and a little bit with humidity â but not with air pressure (atmospheric pressure). The words "sound pressure at sea level" are incorrect and misleading. The temperature indication, however, is absolutely necessary..
The speed of sound a…t 20 degrees Celsius (68 degrees Fahrenheit) is 343 meters per second. That is 1126.547 feet per second. (MORE)

# How do you find Feet per second per second?

That is a measure of acceleration, so if you know the velocity and divide it by the time, it should give you the correct units,

# What is 1000 feet per second to miles per hour?

Equates to approximately 681.82 miles per hour..
Supporting math -.
There are 60 seconds in every minute (multiply 1000 X 60 = 60,000).
There are 60 minutes in every hour (multiply 60,000 X 60 = 3,600,000).
There are 5280 feet in every mile (divide 3,600,000 / 5280 = 681.8181818181).
Does that …answer your question?? (MORE)

# How fast is 60 feet per second?

60 (feet per second) .
65.8368 kph .
60 (feet per second) = 40.9090909 mph ==

# What is the speed of gravity in Feet per second?

The average speed of gravity on the surface of the Earth is 32.1740 ft/s 2 (9.80665 m/s 2 )

# What is the speed of sound in feet per second?

Notice: The speed of sound changes with temperature and a little bit with humidity â but not with air pressure (atmospheric pressure). The words "sound pressure at sea level" are incorrect and misleading. The temperature indication, however, is absolutely necessary..
The speed of sound… in air at 20 degrees Celsius (68 degrees Fahrenheit) is 343 metres per second. That is 1126.547 feet per second. (MORE)

# What are the feet per second model 799.190720?

Approximately 680 FPS for the Daisy model 880 made for Sears under the JC Higgins brand name.

# What does 32 feet per second per second mean?

Take 32 ft/sÂ² and break it down into (32 ft/s)/s It means that every second, the speed of something is increasing by 32ft/s

# Convert feet per minute to feet per second?

'F' (feet / minute) x (1 minute / 60 seconds) = (F / 60) (feet - minute / minute - second) = F/60 ft/sec.
-- Take the number of feet per minute..
-- Divide it by 60..
-- The answer is the number of feet per second.

# How many feet per second is 25 miles per hour?

1 hour = 3,600 seconds.
1 mile = 5,280 feet.
25 miles = (25 x 5,280) ft.
(25 miles) / (1 hour) = (25 x 5,280 ft) / (3,600 sec) = (132,000) / (3,600) = 36 and 2/3 ft/sec

# What is 9.81 meters per second in feet per second?

There are 0.3048 metres in one foot. Therefore, rounded to two decimal places, 9.81 metres per second is equal to 9.81/0.3048 = 32.19 feet per second.

# How many feet per second are there in miles per hour?

1 mile per hour = 22/15 = 1.4666... feet per second (rounded, repeating) The following are exact numbers: -- 15 miles per hour = 22 feet per second -- 30 miles per hour = 44 feet per second -- 60 miles per hour = 88 feet per second -- 90 miles per hour = 132 feet per second -- …120 miles per hour = 176 feet per second (MORE)

# What is 32 feet per second per second?

32 feet per second per second is an example of an acceleration. the acceleration of gravity on earth at sea level is 32.2 feet per sec per sec

# What is 27404 feet per second in miles per hour?

27,404 feet per second = 18,684.5 mph Algebraic Steps / Dimensional Analysis .
27,404 ft/s .
.
3600 ft/hr 1 ft/s .
.
1 mi/hr 5280 ft/hr .
= .
18,684.54545 mi/hr.

# How do you convert meters per second to feet per second?

Multiply (meters/sec) by 3.28084 to get (feet/sec). (rounded) If you don't need it that close, multiply by 3.28 .

# Gallons per minute to square feet per second?

Considering the gallon is a unit of volume (3-D) and square feet it a unit of surface area (2-D), the two are not comparable in this way. Gallons per minute is a rate of flow. Square feet per second is a rate of speed. You may be referring to gpm /square feet - in other words, the amount of liqui…d being applied to a specific unit of surface area. Example: You are flowing 1000 gpm and you want to know the density of that liquid given an area, say a 100' tank. The surface area of the tank = pi * (50)^2 = 7853 square feet. The density of that liquid = rate of flow / surface area = 1000 gpm/ 7853 sq.ft. = 0.12734 gpm/sq.ft. (MORE)

# What is 125 feet per second in miles per hour?

(125 ft/sec) x (1 mi / 5280 ft) x (3600 sec / 1 hr) = (125 x 3600 / 5280) ( ft - mi - sec / sec - ft - hr ) = 85.227 mph (rounded)

# Meters per second to cubic feet per minute?

cubic meters per second (m 3 /s) x 2,119 = cubic feet per minute (ft 3 /min)

# What is the speed of a tiger feet per second?

A tiger can run about 28 mph for short distances. This equates to 41.0667 feet per second.

# How fast is 80 feet per second?

80 ft\sec *60=4800ft\min*60=288,000ft\hour and when divided by 5280 feet\mile that equals 54.55 miles per hour

# How many feet per second is 105mph?

1 mile = 5280 ft 1 hour = 3600 seconds 105 miles/hour = (105 x 5280 ft) / (1 x 3600 seconds) = 154 ft/s .

# What is 66 feet per second?

That would be referred to as a "speed". It can also be described as "45 miles per hour", to which it is identically equivalent.

# What is 50 miles per hour in feet per second?

There are 5280 feet in one mile. Therefore, 50 miles per hour is equal to 50 x 5280 = 264000 feet per hour. There are 3600 seconds in one hour. Therefore, 264000 feet per hour is equal to 264000/3600 = 73.3 recurring (that is, 73.3333...) feet per second.

# How much feet per second does a 410 have?

.410 bore cartridges are made in the U.S. of A in three lengths : 2.5", 2.75 and 3". 3" loadings, typically, generate higher velocities. Velocities (for either size cartridge) of the projectiles will vary with powder loadings. For "shot" shells, which contain small pellets (#8 and #4 are the most co…mmonly found), velocities will range from approximately 1100 feet per second (fps) to close to 1400 fps. For "buck shot" loads (3 or 4 x 000 buck or 8 or 9 x #4 buck, are most common) velocities will range from approx. 1050 fps to 1400 fps. For "slug" loads, which contain a single pellet (usually 87 or 88 grains = approx. 1/5 oz) typical velocities range from 1400 fps to 1800 fps. All these velocities are developed from a standard, smooth bore barrel of around 26". (MORE)

# How do you convert feet per year to meters per second?

1 year = 31,557,600 seconds convert x feet per year to y meters per year y/31,557,600 is the answer.

# How fast is18 feet per second?

It's a speed that's precisely equal to 18 feet per second. In a somewhat more familiar unit, it's 12.273 miles per hour. (rounded)

# How do you convert feet per second to nanometers per millisecond?

Let 'F' = speed in fps. ( 'F' ft/sec) x (10 -3 sec/millisec) x (10 9 nanometer/meter) / (3.28084 ft/meter) = 3.048 F x 10 5 nanometer/milllisec (rounded)

# How fast is 3100 feet per second?

lets convert is into something that is understandable like miles per hour... 3100 ft/sec * (1mile/5280ft) = 0.587121212 miles/sec 0.587121212miles/sec * (60sec/1minutes) * (60minutes/1hour) = 2113.636363mph Therefore 3100ft/sec if extremely fast. It is around 2114miles per hour. This is around 3 …to 4 times faster than an airplane and around 7 times faster than any vehicles created. (MORE)

# What is the formula for traveling feet per second?

formula for speed is metres per second so 1 metre is 3.25 feet so to covert metres per second to feet per second, multiply the metres value by 3.25.

# What is 74 miles per hour in feet per second?

There are 5280 feet in one mile. Therefore, 74 miles per hour is equal to 74 x 5280 = 390720 feet per hour. There are 3600 seconds in one hour. Therefore, 390720 feet per hour is equal ot 390720/3600 = 108.53 recurring (that is, 108.53333...) feet per second.

# How do you convert inches per second to feet per minute?

take the inches and divide them by 12 then take the seconds and divide them by 60 then you will have sucessfully converted inches per second to feet per minute. 120inces =10 ft 180 sec= 3 min therefore you r object is traveling at 3.3333 ft. per sec.

# How fast is 21 feet per second?

That speed is equal to exactly 21 feet per second. In units with which you may be more familiar, it's 14.318 miles per hour. (rounded)

# How fast is 16 feet per second?

Pretty close to 10.91 miles per hour. -- finish a marathon in 2 hours 24 minutes 12.2 seconds (very impressive) -- run a mile in 5 minutes 30 seconds (not too shabby) -- 100 yard dash in 18.75 seconds (loafing) -- cover a straight-line route to the moon in about 909 days (ridiculo…us) (MORE)

# What is 68.75 feet per second in mph?

= 46.875 mph or 46.88 if you want to retain the 4 digits of resolution (significant figures) (I just copied " 68.75 feet per second in mph ", pasted it into my browser and it shows up directly!) (Well done! But where would you be without your browser ? Does anyone know how to calculate thi…s anymore ?) (MORE)

# How do you convert gallons per minute to feet per second?

First convert gallons to a volumetric unit like cubic ft (ft^3) 7.48 gal per ft^3 Then divide the ft^3 quantity by the cross sectional area of the pipe (converted into square feet ft^2) This will leave you with linear units of feet. This number of feet must travel past a point in the pipe i…n one minute to deliver a gallon. You can then do the time conversion to obtain ft/sec from ft/min. Consider a cylinder with a diameter equal to the pipe inside diameter. How tall would that cylinder have to be in order to hold a gallon of water. Its the same type of problem only with the added twist that the water is flowing past a point in a given amount of time.. (MORE)

# How fast is 176 feet per second?

It's the speed of exactly 176 feet per second. Converted into other units of speed, it's also equal to -- 193.12 kilometers per hour (rounded) -- 126,720 inches per minute -- 322,560 furlongs per fortnight -- 4,634.91 kilometers per day (rounded) -- 0.315224 smoot per centisecond (…rounded) -- 120 miles per hour -- 0.00017894 light-year per milennium (rounded) etc. (MORE)

# How fast is 135 feet in per second?

If you go 135 feet in a second, you travel 135*60 feet in a minute: and you would travel 135*60*60 feet in an hour. 5280 feet is a mile, so you would travel (135*60*60)/5280 miles per hour (135*60*60)/5280 = 92 mph (rounded)

# What is 80mph in feet per second?

Use the units to help figure this out. There are 5280 feet per mile = 5280 ft / 1 mile There are 3600 seconds in an hour = 3600 sec / 1 hour 80 Miles / 1 hour = 422400 ft / 1 hour = 422400 ft / 3600 Sec = 117.3333 ft / sec

# How many feet per second walking?

this is different for everyone. measure how far you walk in 100 seconds (1 minute 40 seconds) divide that distance by 100. (456ft= 4.56ft/s) (Average walking speed is 3.7 ft/s)

# What is 5280 feet per second?

It is a measure of speed. It is a measure of speed. It is a measure of speed. It is a measure of speed.

# What is the reciprocal of-.25?

To calculate the reciprocal of any number, divide 1 (the number one) by that number.

# How do you convert from knots to feet per second?

1 knot = 1 nautical mile per hour. Technically 1 nautical mile was the distance subtended by 1 minute of arc along a line of longitude which means at different latitudes it has different lengths (as the earth is geoid in shape - a squashed sphere). However it has been internationally agreed to be… set at 1,852 m exactly or approx 6,076 feet To convert nmi/hr to ft/second, convert to feet/hour by multiplying by 6076 and then divide by 3600 as there are 3600 seconds in each hour: ie multiply the knots by 1.68781 to get approx ft/s (MORE)